ALIBI ALI-NVR3004P Manuel d'utilisateur

ALI-NVR3004P, ALI-NVR3008P Embedded Network Video Recorder User ManualProducts: ALI-NVR3004P, ALI-NVR3008P ALI-NVR3000P Series Network Video Recorde

2• Searching and playing back record les by channel number, recording type, start time, end time, etc.• Motion analysis for the selected area in th

923. Check the Enable NTP box to enable this feature.4. Select the following NTP settings:— Interval: Interval in minutes between the two synchroni

93ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual4. Click Apply to save your settings and close the menu. 7.2.4 ConguringMulticastUsing the m

94SECTION 7: NETWORK SETTINGS3. In the menu shown above, enter the RTSP port number. The default RTSP port is 1050.4. Click Apply to save your setti

95ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual4. Click Apply to save your settings and close the menu. 7.2.7 ConguringEmailThe system can

965. Congure the following Email settings:— Enable Server Authentication (optional): Check the checkbox to enable the server authentication feature

97ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual7.2.8 ConguringUPnP™The Universal Plug and Play (UPnP™) feature allows the device to seamlessl

98SECTION8 System MaintenanceThe Maintenance menus provide several displays that report system device information, log information, and network tra

99ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual2. Select a Start Time, End Time, Major Type and Minor Type. In the example below, the search cr

1008.2.2 LogExportLog information can be exported to a backup device such as a USB storage device. The exported log le is in .txt format and readab

101ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual6. On the Device Name line, open the drop down list and select the destination for the le expo

3ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSECTION 1: SYSTEM OVERVIEW• Remote locking and unlocking of control panel and mouse.• Remote HDD

102Export conguration le3. On the Device Name line, open the drop down list and select the destination for the exported conguration le. 4. Click

103ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual2. In the le list of the USB device, highlight the NVR conguration le you want to load, and

1043. If installing rmware from a local device such as a USB ash drive or disk: a. Connect the local device to the NVR, if necessary. b. Open the

105ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual8.5 DefaultThe default option will reset the NVR to its factory settings. Except the network pa

1068.6.2 TestingNetworkDelayandPacketLoss1. Open the Network Trac menu. Go to Menu | Maintenance | Net Detect2. Click the Network Detection t

107ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual8.6.3 ExportingNetworkPacketBy connecting the NVR to network, the captured network data packe

1088.6.4 CheckingthenetworkstatusYou can also check the network status and quickly set the network parameters. 1. Open the Network Trac menu. Go

109ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual8.6.5 CheckingNetworkStatisticsUse the following procedure to view real time network status o

110SECTION9 Remote AccessIf you NVR is connected to a local network (LAN), you can access it from another computer on the LAN through Microsoft® In

111ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSECTION 9: REMOTE ACCESS2. In the login window, enter your User Name and Password in the approp

4NVR BackpanelCamera (CH1 - CH4)LAN RS-485 Power connector Fan outletON / OFF switchMonitor Out (HDMI, VGA)Audio IN / OUTUSBALI-NVR3004P backpanelA

1129.2 Remote Live View screenThe Live View window initially appears in a multi-screen conguration with no live view images shown. You can:• Change

113ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual— Double click the camera channel you want to see. — To expand the image to full frame, doubl

114Stop playbackDownloadZoomExpand / contract timelinePlay motion controlsRecord legendPlayback timestampCapture Audio play / muteSet playback timeMu

115ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualTo Download recorded video: NOTEThe location where recorded video downloads and captures during

116Log reports can be saved in either text or Excel formats by clicking the Save Log icon.9.5 Remote Conguration screenOpen the Conguration screen

117ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualThe location of local les is dened on the Conguration | Local Conguration screen. SECTION 9:

118SECTION 10: CLEANING SECTION10 CleaningClean the camera lens and IR lamp shield with a mild glass cleaning solution and a lint free cloth. • Re

119ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSECTION 11: SPECIFICATIONSSECTION11 SpecicationsModel ALI-NVR3004P ALI-NVR3008PNumber of Cha

120APPENDIX A: GLOSSARYAPPENDIXA GlossaryDual Stream: Dual stream is a technology used to record high resolution video locally while transmitting a

121ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualAPPENDIX B: FAQAPPENDIXB FAQ Q Why does my NVR make a beeping sound after booting? A The poss

5ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSECTION 1: SYSTEM OVERVIEWItem Name Function1 POWER Power on/o the device.2 DEV Enables/Disables

122APPENDIX C: HDD INSTALLATIONAPPENDIXC HDD InstallationThe following procedures illustrate hard disk drive (HDD) installation in a ALI-NVR3000P se

123ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualAPPENDIX C: HDD INSTALLATION: 3. Orient the chassis as shown in the picture below. Become famil

124APPENDIX C: HDD INSTALLATIONCAUTIONFollow recommended electrostatic discharge (ESD) guidelines while performing this procedure. Install the HDD in

125ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualAPPENDIX C: HDD INSTALLATIONCAUTIONFollow recommended electrostatic discharge (ESD) guidelines

126APPENDIX D: NVR COMPATIBLE CAMERASAPPENDIXD NVR Compatible CamerasFollowing is a list of IP cameras shown to be compatible with your NVR. Other c

127ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualAPPENDIX D: NVR COMPATIBLE CAMERASIPC Manufacturer or ProtocolModel Version Max. Resolution Sub-

128APPENDIX D: NVR COMPATIBLE CAMERASIPC Manufacturer or ProtocolModel Version Max. Resolution Sub-stream AudioHikvision® (cont.)DS-2CD802NFDS-2CD812P

129ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualAPPENDIX D: NVR COMPATIBLE CAMERASIPC Manufacturer or ProtocolModel Version Max. Resolution Sub-

130

61.1.2 MousecontrolA standard 3-button (left/right/scroll-wheel) USB mouse can also be used with this NVR. To use a USB mouse: 1. Plug USB mouse in

7ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSECTION 2: INSTALLING THE SYSTEMSECTION2 Installing the System2.1 Getting Started: Unpacking t

82.2 NVR installation general guidelines2.2.1 InstallinganHDDintheNVRIf you purchased your NVR without an internal HDD, you must install one fo

9ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSECTION 2: INSTALLING THE SYSTEMIf you are using Cat 5e or Cat 6 copper (Ethernet) cable to connec

102.4.1 UsingtheWizardforbasiccongurationsetup1. Power on the NVR. Normally, an Alibi logo splash screen appears within 2 minutes. 2. The Se

11ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual3. Enter the admin password in the appropriate eld. To do that, click inside the Admin Password

iiCAUTIONDo not expose this appliance to rain or moisture. Operate this device only in environments where the temperature or humidity is within the r

125. In the date and time setup window, click the eld you want to change, then use the drop-down list or setup aid to select the appropriate values.

13ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual7. Click Next after you congured the network parameters. The HDD management Wizard window will

14SECTION 2: INSTALLING THE SYSTEMb. Click the Start Recording box to check it. c. Select one of the recording modes: either Normal or Motion Detect

15ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSECTION 2: INSTALLING THE SYSTEMe. Click OK when the recording mode for each camera is selected.

16Live View display after camera adjustments2.5 Access the Menu systemAfter the initial setup of your DVR using the Wizard, the Menus interface enabl

17ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual2.6 Customize camera congurationsThe Camera menu lists all cameras congured in the NVR, and sh

182.6.1 CameraOSDsetup1. Click OSD in the left frame to open the OSD submenu. 2. In the Camera eld drop down list, select the camera you want to

19ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual2. In the Camera eld drop down list, select the camera you want to congure. In the example sho

202. In the Camera eld drop down list, select the camera you want to congure. In the example shown, IP Camera 1 is selected. 3. Check or un-check

21ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manuala. Select the other channels that should trigger recording on this channel, then click Apply to

iiiALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSAFETY INSTRUCTIONS Regulatory informationFCC informationFCC compliance: This equipment has been

22e. Select the actions you want to occur, then click Apply to save your settings, and OK to return to the Motion menu. The Notify Surveillance Cente

23ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual2. In the Camera eld drop down list, select the camera you want to congure. In the example sho

24a. In the Arming Schedule tab, dene a daily schedule for up to eight weeks (56 days) when the camera is monitored for tamper. Time periods cannot

25ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual2.6.6 CameraVideoLosssetup1. Click Video Loss in the left frame to open the Video loss subme

26b. In the Arming Schedule tab, dene a daily schedule for up to eight weeks (56 days) when motion detection is monitored. Time periods cannot overl

27ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manuala. Verify that the manufacturer and model of the camera you want to add is compatible with the N

28d. On the Adding Method line, open the drop down list and select Manual. e. On the IP Camera Address line, click the entry eld and use the pop-up

29ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manuali. Click Apply, and then click OK to close the IP Camera Edit window. j. In the IP Camera scree

303. Click Apply to save the settings, and then click OK to close the menu.2.7.2 ConguringcustomizedprotocolsTo use cameras not congured with th

31ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual6. Select the custom protocol you congured, and then enter the IP address, user name and passwo

iv• Install the unit away from heat sources such as radiators, heat registers and stoves.• Installation of the unit near consumer electronics device

322. Check the status of the HDD. If the status is:— Normal or Sleeping - The HDD is working normally. — Uninitialized or Abnormal - Initialize the

33ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manualii. Select the NAS disk directory from the list shown, or manually enter the directory in the te

34v. Click OK to add the selected IP SAN disk to your system.NOTE: If the added NetHDD is uninitialized, select it and click the Init button for init

35ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manuala. In the Mode select eld, select either Partition or Group. i. If you selected Partition, sel

362. To execute a self-evaluation test on an HDD: a. On the HDD line, open the drop down list to select the HDD of interest. b. On the Self-test Ty

37ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualClick Pause to temporarily stop the scan, and click Cancel to end the scan. Click Error info to s

38To congure exception alarms: 1. Open the Exception menu. Go to Menu | Conguration | Exceptions2. On the Exception Type line, open the drop down

39ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSECTION3 Startup, Shutdown, RebootAfter the DVR and cameras are installed, the DVR system must

40 NOTEThe default User Name with administrative privileges and its associated Password are admin and 1111. 3. In the Menu window, click the Shutdown

41ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSECTION4 Live View InterfaceThe Live View interface is the primary camera viewing and monitori

vALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualTABLE OF CONTENTSTable of ContentsSECTION 1 Systems Overview ...

42Icon Type Reason Record and Alarm Both alarm and record status4.1 Quick Setting ToolbarLeft-clicking the mouse on a viewing frame opens a Quick Set

43ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSECTION 4: LIVE VIEW INTERFACELive View Strategy: Use this feature to select Real-time, Balanced,

44— Multi-screen: opens a submenu where you can choose from several multi-channel screen congurations, including 2 * 2, 1 + 5, 1 + 7, 3 * 3 , in mu

45ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSingle-, multi-screen select icons Viewing screens4. Click the single- or multi-screen select ic

46SECTION5 Record, Playback and Video BackupAfter the initial setup of your NVR using the Wizard, the Menus interface enables you to rene your con

47ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual5.1 Conguring record settings5.1.1 Settingcameraencodingparameters1. Enter the Record sett

48a. Congure the parameters of the camera.b. Click Apply to save the settings.5.1.2 ConguringRecordscheduleThe record schedule can be used to a

49ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual— Open the Schedule line drop down list and select the day you want to create a record schedule

50Copy window for 4-channel NVRii. To use the graphical method to draw the schedule: — Click the color icons on the right for the recording mode, th

51ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualNormal recordingRecording triggered by alarmRecording triggered by motion or alarmRecording trig

viTABLE OF CONTENTS3.1.3 Rebooting the DVR ...40SECTION 4 Live View Interface ...

525.1.3 ConguringMotionDetectionRecordingFollow the steps to set the motion detection parameters. A motion detection events can trigger several k

53ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manuale. In the Handling Trigger Channel window, select the other channels that should trigger recordi

54i. Select the actions you want to occur, then click Apply to save your settings, and OK to return to the Motion Detection menu. The Trigger Alarm O

55ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manuald. When the Attention window opens, click Yes. 3. To disable Manual Record: a. Select Record o

562. To Edit the Holiday schedule.a. Click the icon in the Edit (right) column of the line you want to edit. The Edit window will open. b. In the E

57ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual 2. Click Advanced in the left frame to open the Storage Mode menu.3. Verify that the HDD mode

582. Check the box(es) for the channel(s) you want to investigate.3. Congure the record type, File Type (locked or unlocked), and Start Time and En

59ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manuala. Determine which les you want to protect, and then click the icon in the Lock column to show

60Playback by channel1. Open the Playback menu. Go to Menu | Playback. 2. In the Playback screen, select the camera channel you want to playback. De

61ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual5. You can click the Details button to show when recordings were made with that camera (D1). 6.

viiALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualTABLE OF CONTENTS7.2.3 Conguring Remote Alarm Host ...

628. In the Sync Playback window, select the other cameras you want to play with the camera selected. You can play up to 4 cameras synchronously. Cli

63ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualTo open the Results list ( the right frame - see above), move the mouse pointer to the right edge

645.2.2 PlayingbackamotioneventThe ALI-NVR3004P and ALI-NVR3008P can search for and playback recordings triggered by motion events. 1. Open the

65ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual7. Select the video clip from the list, then click the Play icon associated with it. The control

669. To playback a dierent motion event video clip, click the segment to highlight it, then click the associated Play icon. 5.2.3 PlaybackbyTagYo

67ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualThe control panel at the bottom of the screen is described earlier in this section. See “5.2.1 Pl

68— To change the name of a tag, select (highlight) a tag in the list, then click the icon in the Edit column.* Click the tag name, use the pop-up k

69ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual3. Select a Start Time, End Time, Major Type and Minor Type. 4. Click Search. If the search did

705. Choose a log with record le and click the playback button to play the le, or click the icon in the Details column to see more information abou

71ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual2. On the IP Camera line, select multiple IP cameras by checking the boxes associated with them.

viiiNOTES

725.3 Backing up Record Files - Export5.3.1 QuickExportThe Quick Export feature allows you to easily export (backup to an external device) video cl

73ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual6. If the device you are exporting to is a rewritable device such as a USB ash drive, select th

745.3.2 ExportbyvideosearchThe Export by video search feature allows you to export specic video clips. The export operation writes the selected 

75ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual6. Select the video clips you want to export by clicking the checkbox associated with the le. B

768. In the Export window, select the directory where you want to copy the les, or create a New Folder. 9. Click the Export button to start the Exp

77ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual2. Open the Export menu. Go to: Menu | Export | Event3. On the Event Type line, select open the

787. In the Events Detail window, click Export to open the Export window, or in the Motion (search result) list, check the boxes for the video clips

79ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual9. Click the Export button to start the Export. The Export window will list the les that were t

803. Advance the le playback to the start of the segment you want to export, then click the Clip icon (scissors) at the bottom of the screen to mark

81ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual8. In the Export window, select the directory where you want to copy the les, or create a New F

1ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSECTION 1: SYSTEM OVERVIEWSECTION1 Systems OverviewCongratulations on purchasing your new Embed

82Note: The Player utility player.exe will be exported automatically during video le export. SECTION 5: RECORD, PLAYBACK AND VIDEO BACKUP

83ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSECTION6 Managing User AccountsUser accounts are created to control access to the system both

84— Set the user Level to Operator or Guest. Dierent Levels have dierent operating permission.* Operator: The Operator user level has permission o

85ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual— Local Camera Management: Use for adding, deleting and editing of IP cameras.— Local Advanced

86Camera Conguration— Remote Live View: Remotely viewing live video of the selected camera(s).— Local Manual Operation: Locally starting/stopping m

87ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual3. Click the Delete (trash can) icon to delete the selected user.6.3 Editing a user account1.

88admin user Edit User menu4. Select and edit the menu options as needed: — Operator and Guest: You can edit the user information, including user na

89ALI-NVR3004P, ALI-NVR3008P Embedded NVR User ManualSECTION 7: NETWORK SETTINGSSECTION7 Network Settings7.1 Conguring General SettingsNetwork se

907.2 Conguring Advanced Settings7.2.1 ConguringDDNSIf your NVR is set to use PPPoE as its default network connection, you may set Dynamic DNS (D

91ALI-NVR3004P, ALI-NVR3008P Embedded NVR User Manual— DynDNS: i. Enter Server Address for DynDNS (i.e. members.dyndns.org).ii. In the NVR Domain N